The Mitsubishi Pajero Clearview Towing Mirror is a full aftermarket replacement towing mirror to suit late and current model Pajero’s. (This means they are mounted as a direct replacement for your standard side mirrors.)

The clever design incorporates two different surfaces that provide different but important visuals.

The top mirror has a flat surface that can reflect vision directly down the sides of your vehicle and caravan, while the bottom smaller convex mirror eliminates blind spots by allowing you greater vision out to the lanes beside your vehicle.

Easy adjustments will allow you to quickly switch the mirror to view possible areas of concern… such as your vehicles tyres, wheels or undercarriage of your caravan.

They are much larger than standard Mitsubishi Pajero side mirrors.

In standard driving position, the Clearview mirror has a wider outward reach of approximately 100mm and a total surface area much bigger than the factory mirrors.

When you are ready to tow, the mirror head can slide out and extend a further 100mm! This additional extension allows for massive 200mm of extension in total over your standard side mirrors.

Important Note: The Mitsubishi Pajero side mirrors come standard with or without indicator lights. If your current vehicle mirrors have indicator lights you are required by law to purchase towing mirrors with indicators.

Standard inclusions for the Mitsubishi Pajero Clearview Towing Mirror
12 Month product warranty	Included
Electric lare mirror	Included
Manual small convex mirror	Included
Black or chrome finish	Included
Manual extension	Included
Indicators (if required)	Included
Temperature sensor (if required)	Included
Puddle light	Optional Inclusion
Electric fold-in or extension	Optional Inclusion
Auto dip for reverse	Optional Inclusion
Cameras	Optional Inclusion
Memory adjustments	Optional Inclusion

Buy These Online

Gallery

Front view of the right hand side black Mitsubishi Pajero Clearview Towing Mirror

Front view of the left hand side Clearview Towing Mirror fitted to a Mitsubishi Pajero

Closeup view of the black Clearview Towing Mirror fitted to a late model Pajero

Left mirror side of the Clearview Towing Mirror fitted on the late model Mitsubishi Pajero

Clearview Towing Mirror on the standard position on a late model Pajero showing the top flat mirror and lower convex mirror

Clearview Towing Mirror on the left hand side of a late model Pajero displaying the top section mirror and lower convex mirror

Left side Clearview Towing Mirror fitted to a late model Pajero

Right top view of mirror side of a Clearview Towing Mirror fitted to a late model Mitsubishi Pajero — Right side Clearview Towing Mirror fitted to a late model Mitsubishi Pajero

Quality

Clearview Towing Mirrors are all injection moulded and built from diecast aluminium to provide a firm and stable footing on every vehicle.

Every mirror base is finished on a CNC milling machine, which gives consistent accuracy for a perfect fit to every vehicle.

They are then powder coated in quality tested facilities, ensuring a high level finish.

They have steel arms through the centre of the mirrors, giving them extreme strength. These arms have cams which are precision cut from stainless steel on a high tech water cutting machine.

The cams are welded to the arms for better quality control and consistency. The finished arms are then coated in a special corrosion resistant electro coating paint process.

Installation

Because Clearview Towing Mirrors are a full replacement towing mirror, they are designed to use the existing holes, fittings and wiring as your existing vehicle set-up.

Overall this means a stress-free fitting procedure.

Options

Electric or Manual Operation

Clearview Towing Mirrors can be fully electric – meaning the larger flat mirror glass is capable of being shifted with the flick of a switch from your existing mirror controller – or they can also be fitted as a manual, non-electric mirror.

Please note that Clearview mirrors are not capable of electric folds, memory adjustments or auto dipping for reverse, and they do not contain puddle lights or cameras. If your standard side mirrors contain any of these functions they will be lost once these mirrors are installed. This has no ill effect on any of the other vehicle functions.

With or Without Indicator Lights

Clearview Towing Mirrors can be fitted with or without indicators.

If your vehicle’s standard side mirrors contain indicators then you are required by law to buy replacement side mirrors with indicators.

Some vehicles can have our mirrors with indicators even if the vehicle’s standard side mirrors do not contain indicators.

Chrome or Black Finish

A choice between a chrome or textured black finish is available. While both designs are equably durable and practical and capable of resisting the harsh Australian outback, the chrome mirrors do require a polish every once in a while to maintain their original shine.

Canopies

Ironman 4×4 Thermoplas Canopy Mazda BT-50

June 9, 2015 superior4x4 Leave a comment

Convert the back end of your Mazda BT-50 Dual Cab Ute into a safe, practical, lockable, dry space with an Ironman 4×4 Thermo-Plas Canopy.

Manufactured from a single sheet of solid 9mm ABS plastic and fully lined internally with plush long wearing grey brush carpet.

This Ironman Thermo-Plas canopy is lightweight, super strong, resistant to high impact and built to withstand the harshest Australian conditions, so you know this canopy is going to go the distance.

These canopies have a full range of optional accessories making them ideal for any 4×2 or 4×4 owner and are perfect for everyday use.

Canopy features:

Smooth clean finish with a solid one piece construction
Lift up windows on all three sides
Internal metal supporting frame for extra strength and durability
Plug & play wiring loom
Internal lighting system
Lockable rear single handle for ease of opening and closing
Gas strut for easy opening
Quickfit 4 point clamp system – no drilling required
Stylish design to suit vehicle contours and maintain the vehicles good looks
Built in rear LED brake light
Roof rack and bars rated to 80kg of carrying capacity
The glass is tempered and tinted providing extra safety while also keeping your cargo area
nice and cool
The rear allows for maximum access with the widest possible opening
Each side window reaches 80% of the full length of the unit
Using the latest rubber seals the Ironman canopy provides a dust and water free environment

SKU: CANOPY011A

Find Out More

Right side view of the Ironman 4x4 Thermoplas Canopy fitted to a current model Mazda BT-50 — Right side view of the Ironman 4×4 Thermoplas Canopy fitted to a current model Mazda BT-50

Sleak Roof rack and rails are available for the Ironman Thermo-plas Canopy

Rear view of the Ironman 4x4 Thermoplas Canopy with all the windows closed — Rear view of the Ironman 4×4 Thermoplas Canopy with all the windows closed

Rear view of BT-50 fitted with an Ironman 4x4 Thermo-plas Canopy with all the windows open — Rear view of BT-50 fitted with an Ironman 4×4 Thermo-plas Canopy with all the windows open

Rear view of Mazda BT50 with the Ironman Thermoplas Canopy with the rear and side windows fully opened and rear vehicle tray down

The interior roof and walls are finished with a plush hard wearing brush carpet

There is an interior gas strut mounted to the rear window to help opening and closing the canopy a breeze

Right side view of the canopy window fully open while fitted to the Mazda BT-50 Dual Cab Ute

Internal quickfit system and clamp makes for an easy process of installing the canopy to the Mazda BT-50

Closeup view of the back canopy window lockable handle for opening and closing the rear of the canopy

Call (07) 5433 1411 More

*Product may vary from images shown

Recovery, Recovery Kits

T-Max 8 Piece Vehicle Recovery Kit

May 29, 2015 superior4x4 1 Comment

This Heavy Duty T-Max 8 Piece Vehicle Recovery Kit is an essential piece of equipment for any four wheel drive enthusiast.

It is very important to have quick and easy access to all your recovery equipment, so this kit comes in a super strong tough duffle bag.

Each T-Max recovery kit has been carefully tailored to include the correct equipment for most recovery situations.

Best suited to the 4WD enthusiast who has a winch fitted to their vehicle.

Designed to maximise winch capabilities, performance and versatility.

This 8 piece kit offers the ability to self recover or perform a snatching recovery.

Includes the following components:

8T Snatch Strap – 9 metre x 60 mm
- All T-Max snatch straps are made and tested to meet the highest quality and strength standards in Australia. They are manufactured from 100% treated nylon webbing with reinforced eyelets to prolong operational life.
4T Winch Strap – 10 metre x 50 mm
- An winch strap is the ideal accessory for any winch, be it either a hand winch or electric winch. They are used to extend the length of a winch cable if it’s not long enough to anchor to a recovery point when fully extended.
8T Tree Trunk Protector – 3 metre x 75 mm
- The T-Max tree trunk protector is designed to protect the tree used as an anchor point for your recovery. If you use anything other than a tree trunk protector you risk damaging both the tree and your winching line.
8T Snatch Block
- These snatch blocks reduce the load placed on the winch while performing a vehicle recovery and to avoid damage when changing the direction of the cable. The T-Max snatch block has two outer steel casings which swivel apart and allow the winch cable to be placed over the pulley wheel.
4.75T Bow Shackle
4.75T D Shackle
Pair of Leather Gloves
- These T-Max leather recovery gloves have been made using a premium grain leather. Feature stitch free palms, winged thumb area and elastic cuffs. Wearing safety gloves are extremely important when using recovery accessories, equipment or winch cable as they offer optimal protection to your hands.
Heavy Duty Recovery Bag

Features: High visibility safety yellow, high strength nylon webbing, reinforced stitched eyelets, long wearing, superb quality and durability.

Pair of leather safety gloves that come standard in the T-Max kit

T-Max 8T Tree Trunk Protector - 3 metre x 75 mm — T-Max 8T Tree Trunk Protector – 3 metre x 75 mm

T-Max 8T Snatch Strap - 9 metre x 60 mm — T-Max 8T Snatch Strap – 9 metre x 60 mm

T-Max 4T Winch Strap - 10 metre x 50 mm — T-Max 4T Winch Strap – 10 metre x 50 mm

T-Max complete 8 Piece Vehicle Recovery Kit

Call (07) 5433 1411

Leaf Springs, Suspension

Ironman 4×4 Leaf Springs

April 22, 2015 superior4x4 1 Comment

Description:

Ironman 4×4 produce a wide range of Leaf Springs to suit a range of load ratings… all designed to maintain optimum ride height.

Ironman 4×4 Leaf springs are produced from high quality steel that meets Australian standard AS1447 which are shot peened and load tested to ensure maximum longevity.

Available for different load varieties, to ensure the ride is perfectly matched to your requirements by being both strong and flexible.

Leaf Springs produced by Ironman 4×4 undergo class leading manufacturing processes to ensure the highest possible quality.

Features:

Inter-Leaf Liners

Used in some applications to lower friction between leaves reducing noise and improving comfort.

Lined Bolt Clamps

All Ironman springs feature bolted guide clamps for greater flex. The addition of anti-friction liners ensures noise free and ultra smooth operation.

Shot Peened

Shot peening manipulates the spring materials surface tension to reduce stress and will enhance and extend the springs life.

Diamond Cut Leaves

Distributes load at the leaf tip and reduces interleaf friction.

Military Wrap

Where applicable, an additional wrap around the leaf eye protects from failure in case of damage.

Find Out More

Right side view of some steel leaves from an Ironman 4x4 Leaf Spring — Right side view of some steel leaves from an Ironman 4×4 Leaf Spring

Left side view of some steel sleeves, rebound clip, central clamp from a new set of Ironman 4x4 Leaf Springs — Left side view of some steel sleeves, rebound clip, central clamp from a new set of Ironman 4×4 Leaf Springs

Full complete new set of Ironman 4x4 Leaf Springs — Full complete new set of Ironman 4×4 Leaf Springs

View of the pin mount end of the leaf spring

View of the graduated leaf springs and the load bearer

Close up view of the shackle mount end of the leaf spring

Close up view of the rebound clip enclosing the leaves and load bearers from the leaf spring

Top down view of the support mount, main clamp and rebound clip of the Ironman spring

Close up view of the military style wrap common on leaf style springs

The Ironman 4x4 leaf spring laying on its end ready to be shipped out — The Ironman 4×4 leaf spring laying on its end ready to be shipped out

FAQ’s:

What is unique about Ironman leaf springs?

The thing that makes Ironman leaf springs unique is that they’re designed to match driving style and vehicle use.

Ironman concentrates on improving ride, handling, comfort and control, while also providing lift. These design concerns are made without compromising safety and will make driving your vehicle a pleasure.

Ironman leaf springs allow you to choose the right design of springs that suits your driving style. So whether you drive on road, off road or with a constant load you can find the right spring that suits your needs.

How much lift can I expect from Ironman 4×4 springs?: Ironman leaf springs generally lift vehicles around 50mm above the normal vehicle ride height.

Will my vehicle ride firmer after fitting Ironman leaf springs?: Yes it can. While Ironman springs will firm the ride and support the load… used in conjunction with Ironman Shocks, the ride will also become noticeably smoother.

Call (07) 5433 1411 More

Drawer Systems

MSA 4×4 Fridge Drop Slide

April 20, 2015 superior4x4 54 Comments

The MSA 4×4 Fridge Drop Slide was designed in Australia to handle the needs of harsh outback touring.

Manufactured from a premium powder coated steel frame with a Blue anodised aluminium handle, faceplate and handle brackets. These features give you a tuff, durable and attractive finish.

The top quality over extension roller bearing slides will allow you to easily clear your drawer system and most ute sides.

Gas struts and roller carrier bearings ensure the smooth and almost effortless controlled movement to lower and raise your fridge, freezer, generator or tool box.

Key locks, runner locks and a supplied tie down kit will keep your tray and fridge securely in place while you’re traveling.

These drop slides and the working components have been put through extensive and continuing product testing. They have been tested all over Australia in some of the toughest terrains to ensure our build quality will take just about anything.

These MSA Drop Slides are apart of thousands of Aussie tourers who travel every day.

“Best thing I’ve ever bought. Simply the best accessory for my 4WD vehicle!” Many Happy Customers

Find Out More

Features :

Bearings, gas struts and locks are designed to take whatever the rough outback delivers.
Drops your fridge for easy and visual access to items enclosed.
Effortless fridge return with the lever arm placing the fridge back in its location.
Blue anodised aluminium handle, faceplate and handle brackets.
Runners have a lock-in and lock-out mechanism.
Tie down straps are now included to secure your fridge / freezer.
Will only raise your fridge / freezer by 35mm.

Click here to see which portable fridges will suit the MSA 4×4 DS40 Fridge Drop Slide.

Click here to open the drop down slide installation instructions.

Click Here To Open Fridge Sizing Guide

Note: The fridge samples are only a guide, please use the external measurements of your fridge against the fridge tray dimensions.

Note: Some fridge bags may obstruct the full use of the slide.